Datapoint Newsletter: Fall 2022, Vol. 28.2
DatapointLabs Invests in New Testing Capabilities, Expands Market Reach
Read full postDetermination and Use of Material Properties for Finite Element Analysis: Book Review
This book is intended to be a companion to the NAFEMS book, "An Introduction to the Use of Material Models in FE". It informs Finite Element Analysis users of the manner and methodologies by which materials are tested in order to calibrate material models currently implemented in various FEA programs. While the authors seek first to satisfy the basic material models outlined in the companion book, they make important extensions to FEA used in currently active areas including explicit simulation.
Read full postUsing an Intermediate Validation Step to Increase CAE Confidence
Simulations contain assumptions and uncertainties that a designer must evaluate to obtain a measure of accuracy. The assumptions of the product design can be differentiated from the ones for the solver and material model through the use of a mid-stage validation. An open loop validation uses a controlled test on a standardized part to compare results from a simulation to the physical experiment. From the validation, confidence in the material model and solver is gained. In this study, the material properties of a polypropylene are tested to characterize for an *ELASTIC *PLASTIC model in ABAQUS. A validation of a quasi-static three-point bending experiment of a parallel ribbed plate is then performed and simulated. A comparison of the strain fields resulting from the complex stress state on the face of the ribs obtained by digital image correlation (DIC) vs. simulation is used to quantify the simulation's fidelity.
Read full postMold Tempering: Conformal Cooling - yes or no?
The tempering layout for injection molds is often designed departing from previous experiences. The manufacturing feasibility is the main driver when deciding where to place cooling lines. However, often the relevance of the tempering in the process profitability or in the part quality is underestimated, and due to the lack of better information sometimes the resulting tempering performs far from the optimum. As a consequence, the molding efficiency is reduced, the part quality is compromised and, once the mold is already built, sometimes expensive trial-and-error is required to bring the mold to an optimum configuration.
Read full postEjection system design: Optimization with SIGMASOFT Virtual Molding
As the demand for functional integration and the need of design differentiation in manufactured products increase, the complexity of plastic parts increases as well; thus some previous knowledge on effective ejection systems becomes insufficient and the challenges in the design of ejection systems grow consistently.
Read full postCold Runner Design - Getting the whole picture matters
The profitability of a molded rubber product depends to a large extent on the mold efficiency. To achieve the maximum productivity, besides the larges possible number of cavities it is desirable to minimize the rubber consumption and to produce parts without defects.
Read full postCreep modelling of Polyolefins using artificial neural networks
Notwithstanding the increasing demand for polymeric materials in an extraordinary variety of applications, the engineers have often only limited tools suitable for the design of parts made of polymers, both in terms of mathematical models and reliable material data, which together constitute the basis for a finite-elements based design. Within this context, creep modelling constitutes a clear example of the needs for a more refined approach. An accurate prediction of the creep behaviour of polymers would definitely lead to a more refined design and thus to a better performance of the polymeric components. However, a limited number of models is available within the f.e. codes, and when the model complexity increases, it becomes sometimes difficult fitting the models parameters to the experimental data. In order to predict the polymer creep behaviour, this paper proposes a solution based on artificial neural networks, where the experimental creep curves are used to determine the parameters of a neural network which is then simply implemented in an Abaqus user subroutine. This allows to avoid the implementation of a complex material law and also the difficulties related to match the experimental data to the model parameters, keeping easily into account the dependence on stress and temperature. After a discussion of the selection of the appropriate network and its parameters, an example of the application of this approach to polyolefins in a simplified test case is presented.
Read full postProviding an Experimental Basis in Support of FEA
The use of CAE in design decision-making has created a need for proven simulation accuracy. The two areas where simulation touches the ground are with material data and experimental verification and validation (V&V). Precise, well designed and quantitative experiments are key to ensure that the simulation initiates with correct material behavior. Similar validation experiments are needed to verify simulation and manage the risk associated with this predictive technology.
Read full postThe Use of Digital Image Correlation (DIC) and Strain Gauges to Validate Simulation
As part of Cornell University's mechanical engineering curriculum and study of classical beam theory, an aluminium beam is deformed to a specific load. Theoretical strains are calculated at certain points along the beam using beam theory, and then verified by using strain gauges placed at these points on the beam. This experiment is then extended to simulation of the same test setup in simulation software, where strains are analyzed at the same points. Discrepancies between the simulation, theory, and strain gauge results have often plagued the test, especially when incorporating more complex beam design. Through use of digital image correlation (DIC) it is possible to pinpoint some of the problem areas in the beam analysis and provide a better understanding of the localized strains that occur at any point in the deformed beam. The use of DIC provides a full field validation of simulation data, rather than a single spot check that strain gauges can provide. This validation technique helps to eliminate error that is associated with strain gauge placement and the possibility of missing strain hot spots that can arise when analyzing complex deformations or geometries.
Read full postValidating Simulation Using Digital Image Correlation
There is interest in quantifying the differences between simulation and real life experimentation. This kind of work establishes a baseline for more complex simulations bringing a notion of traceability to the practice of CAE. We present the use of digital image correlation as a way to capture strain fields from component testing and compare these to simulation. Factors that are important in ensuring fidelity between simulation and experiment will be discussed.
Read full post