Material Insights by Model Type

Rate Dependency

Sort byDateViews

Simulating anisotropy with Ls-dyna in glass-reinforced, polypropylene-based components

by Massimo Nutini5,779 views

Glass-fiber-reinforced polypropylene (GF PP) materials are increasingly being used by customers to replace metal and engineering polymers in structural automotive applications. Like all glass-fiber reinforced thermoplastics, GF PP products can show anisotropy caused by fiber orientation that is induced by the injection process. Taking into account fiber orientation in the simulations enables designers to improve the accuracy of the analyses. This can help prevent arbitrary choices and assumptions when setting material parameters, which become mandatory when an isotropic material law is used. The method proposed in this paper takes advantage of the availability within Ls-dyna of an anisotropic material law (MAT_103), which allows simplified modeling to address critical issues. This law was not developed to address the problem discussed here. Therefore, this paper illustrates a simplified approach. The presence of glass reinforced fibers is taken into account by running a mold-filling analysis, and then transferring the material flow orientation in to the structural simulation as a material angle. The dependence of the material failure strain on the material orientation can be also easily modeled through a user subroutine. Finally, the approach only requires simple material data based on basic tensile tests; the material law parameters are then identified through optimization techniques. Although this approach is based on some simplifying assumptions, its application is quick and can help the designer obtain more accurate results with respect to the traditional isotropic approach. A selection of validation tests is then proposed that show reliable predictions using limited additional computational effort.

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalPlasticsRate DependencyResearch Papers

Caratterizzazione di materiali plastici: misure locali di deformazione per la simulazione ad elementi finiti di problemi di impatto

by Massimo Nutini5,363 views

Questo articolo si propone di illustrare l’importanza dell’utilizzo di metodi per la misura delle proprietà locali del materiale per determinarne la legge di comportamento. Vengono di seguito presentati alcuni esempi che evidenziano quanto più accurate e realistiche siano le simulazioni numeriche di test di trazione ad alta velocità su provini di poliolefine, quando vengano utilizzate proprietà dei materiali rilevate con misure locali, utilizzando metodi ottici. La disponibilità di misure locali e più accurate evidenzia come sia necessario che nei codici di calcolo commerciali vengano implementate delle leggi di materiale più sofisticate di quelle disponibili attualmente, che sono state per lo più originariamente sviluppate per materiali metallici, e dunque non riescono sempre a predire correttamente il comportamento dei componenti in materiali polimerici.

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalPlasticsRate DependencyResearch Papers

Enhanced Failure Prediction in Sheet Metal Forming Simulations through Coupling of LS-DYNA and Algorithm Crach

by Helmut Gese5,343 views

"In sheet-metal-forming the forming limit curve (FLC) is used for ductile sheets to predict fracture in deep drawing. However the use of the FLC is limited to linear strain paths. The initial FLC cannot be used in a complex nonlinear strain history of a deep drawing process or a successive stamp and crash process including a significant change in strain rate. The CRACH software has been developed to predict the forming limit of sheets for nonlinear strain paths [1]. It has been validated to predict instability for bilinear strain paths with static loading in the first path and dynamic loading in the second path for mild steels [2]. As the postprocessing of strain paths from single finite elements in CRACH is not economic for industrial applications MATFEM initiated a project to couple CRACH directly with FEM-Code LS-DYNA using a userdefined material model. This allows a prediction of possible failure during the simulation for all elements with respect to their complete strain history. A special strategy has been developed to include CRACH without extensive increase in total CPU time. The developed interface to LS-DYNA allows also the implementation of other failure criteria demanding the history of deformation like for example a tensorial fracture criterion. In order to test the reliability of the calculated safety factor experimental tests for bilinear strain paths have been simulated [2]. In this case the experimental and numerical investigations have been made on two-stage forming processes (static in the 1st stage and both static/dynamic in the 2nd stage) . The static-static case should simulate a stamping process with bilinear strain path. The static-dynamic case should simulate a successive stamp and crash process. The simulation of a complex deep drawing problem including areas with significantly nonlinear strain paths has been simulated with LS-DYNA/CRACH-coupling. It can be shown that the prediction of CRACH can differ significantely from a “standard” prediction based on the initial FLC. The coupling of LS-DYNA and CRACH showed the potential to predict possible fracture in deep drawing and crash loading at an early design stage and allowed to optimise geometry and material quality to significantly reduce later problems in real components."

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalMetalsRate DependencyResearch PapersYielding/Failure Analysis

A Systematic Approach to Model Metals, Compact Polymers and Structural Foams in Crash Simulations with a Modular User Material

by Helmut Gese5,899 views

"Today the automotive industry is faced with the demand to build light fuel-efficient vehicles while optimizing its crashworthiness and stiffness. A wide variety of new metallic and polymeric materials have been introduced to account for these increased requirements. Numerical analysis can significantly support this process if the analysis is really predictive. Within the numerical model a correct characterization of the material behaviour – including elasto-viscoplastic behaviour and failure - is substantial. The particular behaviour of each material group must be covered by the material model. The user material model MF GenYld+CrachFEM allows for a modular combination of phenomenological models (yield locus, strain hardening, damage evolution, criteria for fracture initiation) to give an adequate representation of technical materials. This material model can be linked to LS-DYNA when using the explicit-dynamic time integration scheme. This paper gives an overview on the material characterization of ultra high strength steels (with focus on failure prediction), non-reinforced polymers (with focus on anisotropic hardening of polymers), and structural foams (with focus on compressibility and stress dependent damage evolution) with respect to crash simulation. It will be shown that a comprehensive material model - including damage and failure behaviour - enables a predictive simulation without iterative calibration of material parameters. A testing programme has been done for each material group in order to allow a fitting of the parameters of the material model first. In a second step different component tests have been carried out, which were part of a systematic procedure to validate the appropriate predictions of the crash behaviour with LS-Dyna and user material MF_GenYld+CrachFEM for each material group."

Read full post
AutomotiveFoamsHigh Speed TestingLS-DYNAMechanicalMetalsPlasticsRate DependencyResearch PapersYielding/Failure Analysis

Improved Plasticity and Failure models for Extruded MgProfiles in Crash Simulations

by Helmut Gese5,638 views

"The Crash Simulation of Magnesium Structures with Finite Element Methods demands the use of suitable material and failure models. An associated plasticity model describing the complex asymmetric yield behaviour in tension and compression of Mg extrusions has been developed during the InMaK-project (Innovative Magnesium Compound Structures for Automobile Frames) supported by the German Federal Ministry for Education and Research (BMBF). Differences to the material model 124 in LS-DYNA are exposed. In order to describe the failure behaviour of Mg extrusions under multiaxial loading in FEM crash simulation this constitutive model has been combined with a fracture model for ductile and shear fracture. The fracture model has been added to the user defined constitutive magnesium model in LS-DYNA. The experimental investigations carried out on model components are compared with numerical derived results. Experimental methods for fracture parameter evaluation are shown and general aspects of metal failure due to fracture as well as different modelling techniques are discussed."

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalMetalsRate DependencyResearch PapersYielding/Failure Analysis

Development, implementation and Validation of 3-D Failure Model for Aluminium 2024 for High Speed Impact Applications

by Paul Du Bois6,141 views

FAA William J Huges Technical Center (NJ) conducts a research project to simulate failure in aeroengines and fuselages, main purpose is blade-out containment studies. This involved the implementation in LS-DYNA of a tabulated generalisation of the Johnson-Cook material law with regularisation to accommodate simulation of ductile materials.

Read full post
Aerospace and DefenseAutomotiveHigh Speed TestingLS-DYNAMechanicalMetalsPresentationsRate DependencyValidationYielding/Failure Analysis

A Material Model for Transversely Anisotropic Crushable Foams in LS-DYNA

by Paul Du Bois6,014 views

"Recently new materials were introduced to enhance different aspects of automotive safety while minimizing the weight added to the vehicle. Such foams are no longer isotropic but typically show a preferred strong direction due to their manufacturing process. Different stress/ strain curves are obtained from material testing in different directions. A new material model was added to the LS-DYNA code in order to allow a correct numerical simulation of such materials. Ease-of-use was a primary concern in the development of this user-subroutine: we required stress/ strain curves from material testing to be directly usable as input parameters for the numerical model without conversion. The user-subroutine is implemented as MAT_TRANSVERSELY_ANISOTROPIC_CRUSHABLE_FOAM, Mat law 142 in LS-DYNA Version 960-1106. In this paper we summarize the background of the material law and illustrate some applications in the field of interior head-impact. The obvious advantage of incorporating such detail in the simulation lies in the numerical assessment of impacts that are slightly offset with respect to the foam’s primary strength direction."

Read full post
AutomotiveFoamsHigh Speed TestingLS-DYNAMechanicalRate DependencyResearch Papers

Development of Material Input Data for Solid Elements under Crash Loads

by Paul Du Bois5,760 views

"Heavy trucks have large masses and only small deformation zones. Because of this, they are loaded relatively severe in case of a crash. Under those conditions structural response is characterised not only by plastic deformation but also by failure in terms of cracks or fracture. Hence, failure prediction is essential for designing such parts. The following article describes the procedure of generating material models for failure prognosis of solid parts in the Commercial Vehicles Division at Daimler. Sheet metal parts are mostly discretised by shell elements. In this case the state of stress is characterized by hydrostatic pressure over von-Mises effective stress, the so-called triaxiality. For many real-life load cases which can be modeled by thin shells this ratio is between –2/3 and –2/3. Within this range the Gurson material model with the Tvergaard Needlemann addition leads to sufficiently accurate results. Furthermore, the Gurson material model allows considering the effect of element size, which amongst others is important for ductile materials. Most often however, in the case of solid parts the state of stress is more complex, which results in a triaxiality smaller than –1 or larger than 2/3. Gurson material models are usually validated based on shell meshes and tensile tests with flat bar specimen. If applied to solid parts, these models tend to underpredict failure . Thus, for solid parts the GURSON_JC material model is used. The Johnson Cook parameters are derived from an existing Gurson material model. Afterwards the material model is adapted to test results by modifying the load curve giving failure strain against triaxiality. This requires tensile tests"

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalMetalsRate DependencyResearch PapersValidationYielding/Failure Analysis

A Constitutive Formulation for Polymers Subjected to High Strain Rates

by Paul Du Bois5,325 views

"Reliable prediction of the behavior of structures made from polymers is a topic under considerable investigation in engineering practice. Especially, if the structure is subjected to dynamic loading, constitutive models considering the mechanical behavior properly are still not available in commercial finite element codes yet. In our paper, we present a new constitutive law for polymers which recovers important phenomena like necking, crazing, strain rate dependency, unloading behavior and damage. In particular, different yield surfaces in compression and tension and strain rate dependent failure, the latter with damage induced erosion, is taken into account. All relevant parameters are given directly in the input as load curves, i.e. time consuming parameter identification is not necessary. Moreover, the models by von Mises and Drucker-Prager are included in the description as special cases. With the present formulation, standard verification test can be simulated successfully: tensile and compression test, shear test and three point bending tests."

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalPlasticityPlasticsRate DependencyResearch PapersYielding/Failure Analysis