Material Insights by Model Type

Yielding/Failure Analysis

Sort byDateViews

Improved Plasticity and Failure models for Extruded MgProfiles in Crash Simulations

by Helmut Gese5,638 views

"The Crash Simulation of Magnesium Structures with Finite Element Methods demands the use of suitable material and failure models. An associated plasticity model describing the complex asymmetric yield behaviour in tension and compression of Mg extrusions has been developed during the InMaK-project (Innovative Magnesium Compound Structures for Automobile Frames) supported by the German Federal Ministry for Education and Research (BMBF). Differences to the material model 124 in LS-DYNA are exposed. In order to describe the failure behaviour of Mg extrusions under multiaxial loading in FEM crash simulation this constitutive model has been combined with a fracture model for ductile and shear fracture. The fracture model has been added to the user defined constitutive magnesium model in LS-DYNA. The experimental investigations carried out on model components are compared with numerical derived results. Experimental methods for fracture parameter evaluation are shown and general aspects of metal failure due to fracture as well as different modelling techniques are discussed."

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalMetalsRate DependencyResearch PapersYielding/Failure Analysis

Development, implementation and Validation of 3-D Failure Model for Aluminium 2024 for High Speed Impact Applications

by Paul Du Bois6,141 views

FAA William J Huges Technical Center (NJ) conducts a research project to simulate failure in aeroengines and fuselages, main purpose is blade-out containment studies. This involved the implementation in LS-DYNA of a tabulated generalisation of the Johnson-Cook material law with regularisation to accommodate simulation of ductile materials.

Read full post
Aerospace and DefenseAutomotiveHigh Speed TestingLS-DYNAMechanicalMetalsPresentationsRate DependencyValidationYielding/Failure Analysis

Theoretical Development of an Orthotropic Elasto-Plastic Generalized Composite Material Model

by Paul Du Bois6,223 views

The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites is becoming critical as these materials are gaining increased usage in the aerospace and automotive industries. While there are several composite material models currently available within LS-DYNA, there are several features that have been identified that could improve the predictive capability of a composite model. To address these needs, a combined plasticity and damage model suitable for use with both solid and shell elements is being developed and is being implemented into LS-DYNA as MAT_213. A key feature of the improved material model is the use of tabulated stress-strain data in a variety of coordinate directions to fully define the stress-strain response of the material. To date, the model development efforts have been focused on creating the plasticity portion of the model. The Tsai-Wu development efforts have focused on creating the plasticity portion of the model. The Tsai-Wu composite failure model has been generalized and extended to a strain-hardening based orthotropic material model with a non-associative flow rule. The coefficients of the yield function, and the stresses to be used in both the yield function and the flow rule are computed based on the input stress-strain curves using the effective plastic strain as the tracking variable. The coefficients in the flow rule are computed based on the obtained stress-strain data. The developed material model is suitable for implementation within LS-DYNA for use in analyzing the nonlinear response of polymer composites.

Read full post
Aerospace and DefenseAutomotiveCompositesHigh Speed TestingLS-DYNAMechanicalPlasticityResearch PapersValidationYielding/Failure Analysis

Verification and Validation of a Three-Dimensional Generalized Composite Material Model

by Paul Du Bois5,840 views

"A general purpose orthotropic elasto-plastic computational constitutive material model has been developed to accurately predict the response of composites subjected to high velocity impact. The three-dimensional orthotropic elasto-plastic composite material model is being implemented initially for solid elements in LS-DYNA® as MAT213. In order to accurately represent the response of a composite, experimental stress-strain curves are utilized as input, allowing for a more general material model that can be used on a variety of composite applications. The theoretical details are discussed in a companion paper. This paper documents the implementation, verification and validation of the material model using the T800-F3900 fiber/resin composite material."

Read full post
Aerospace and DefenseAutomotiveCompositesHigh Speed TestingLS-DYNAMechanicalPlasticityResearch PapersValidationYielding/Failure Analysis

Development of Material Input Data for Solid Elements under Crash Loads

by Paul Du Bois5,760 views

"Heavy trucks have large masses and only small deformation zones. Because of this, they are loaded relatively severe in case of a crash. Under those conditions structural response is characterised not only by plastic deformation but also by failure in terms of cracks or fracture. Hence, failure prediction is essential for designing such parts. The following article describes the procedure of generating material models for failure prognosis of solid parts in the Commercial Vehicles Division at Daimler. Sheet metal parts are mostly discretised by shell elements. In this case the state of stress is characterized by hydrostatic pressure over von-Mises effective stress, the so-called triaxiality. For many real-life load cases which can be modeled by thin shells this ratio is between –2/3 and –2/3. Within this range the Gurson material model with the Tvergaard Needlemann addition leads to sufficiently accurate results. Furthermore, the Gurson material model allows considering the effect of element size, which amongst others is important for ductile materials. Most often however, in the case of solid parts the state of stress is more complex, which results in a triaxiality smaller than –1 or larger than 2/3. Gurson material models are usually validated based on shell meshes and tensile tests with flat bar specimen. If applied to solid parts, these models tend to underpredict failure . Thus, for solid parts the GURSON_JC material model is used. The Johnson Cook parameters are derived from an existing Gurson material model. Afterwards the material model is adapted to test results by modifying the load curve giving failure strain against triaxiality. This requires tensile tests"

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalMetalsRate DependencyResearch PapersValidationYielding/Failure Analysis

Experimental and Numerical Investigation of Fracture in Aluminium

by Paul Du Bois5,801 views

"To assess the problem of containment after a blade-off accident in an aero-engine by numerical simulation the FAA has instigated a research effort concerning failure prediction in a number of relevant materials. Aluminium kicked off the program which involved an intensive testing program providing failure data under different states of stress, different strain rates and different temperatures. In particular split Hopkinson bars were used to perform dynamic punch tests on plates of different thicknesses allowing to investigate the transition between different failure modes such as petaling and plugging. Ballistic impact tests were performed at NASA GRC for the purpose of validation. This paper focuses on the numerical simulation effort and a comparison with experimental data is done. The simulations were performed with LS-DYNA and a tabulated version of the Johnson-Cook material law was developed in order to increase the generality, flexibility and user-friendliness of the material model."

Read full post
Aerospace and DefenseHigh Speed TestingLS-DYNAMechanicalMetalsResearch PapersValidationYielding/Failure Analysis

A Constitutive Formulation for Polymers Subjected to High Strain Rates

by Paul Du Bois5,325 views

"Reliable prediction of the behavior of structures made from polymers is a topic under considerable investigation in engineering practice. Especially, if the structure is subjected to dynamic loading, constitutive models considering the mechanical behavior properly are still not available in commercial finite element codes yet. In our paper, we present a new constitutive law for polymers which recovers important phenomena like necking, crazing, strain rate dependency, unloading behavior and damage. In particular, different yield surfaces in compression and tension and strain rate dependent failure, the latter with damage induced erosion, is taken into account. All relevant parameters are given directly in the input as load curves, i.e. time consuming parameter identification is not necessary. Moreover, the models by von Mises and Drucker-Prager are included in the description as special cases. With the present formulation, standard verification test can be simulated successfully: tensile and compression test, shear test and three point bending tests."

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalPlasticityPlasticsRate DependencyResearch PapersYielding/Failure Analysis

A Comparative Review of Damage and Failure Models and a Tabulated Generalization

by Paul Du Bois7,793 views

"Reliable prediction of damage and failure in structural parts is a major challenge posed in engineering mechanics. Although solid material models predicting the deformation behaviour of a structure are increasingly available, reliable prediction of failure remains still open. With SAMP (a Semi-Analytical Model for Polymers), a general and flexible plasticity model is available in LS-DYNA since version 971. Although originally developed for plastics, the plasticity formulation in SAMP is generally applicable to materials that exhibit permanent deformation, such as thermoplastics, crushable foam, soil and metals. In this paper, we present a generalized damage and failure procedure that has been implemented in SAMP and will be available in LS-DYNA soon. In particular, important effects such as triaxiality, strain rate dependency, regularization and non-proportional loading are considered in SAMP. All required physical material parameters are provided in a user-friendly tabulated way. It is shown that our formalism includes many different damage and failure models as special cases, such as the well-known formulations by Johnson-Cook, Chaboche, Lemaitre and Gurson among others. "

Read full post
AutomotiveHigh Speed TestingLS-DYNAMechanicalPlasticityPlasticsRate DependencyResearch PapersYielding/Failure Analysis

Accuracy Issues in the Simulation of Quasi-Static Experiments for the Purpose of Mesh Regularization

by Paul Du Bois5,676 views

Generating a LS-DYNA material model from cupon-level quasi-static experimental data, developing appropriate failure characteristics, and scaling these characteristics to mesh sizes appropriate for a variety of simulation models requires a regularization procedure. During an Investigation of an anisotropic material model for extruded aluminum, numerical accuracy issues led to unrealistic mesh regularization curves and non-physical simulation behavior. Sensitivity problems due to constitutive material behavior, small mesh sizes, single precision simulations, and simulated test velocity all contributed to these accuracy issues. Detailed analysis into the sources of innaccuracy led to the conclusion that in certain cases, double precision simulations are necesscary for accurate material characterization and mesh regularization.

Read full post
Aerospace and DefenseAutomotiveExtrusionLS-DYNAMechanicalMetalsNonlinear Material ModelsResearch PapersYielding/Failure Analysis

A Simplified Approach for Strain-Rate Dependent Hyperelastic Materials with Damage

by Paul Du Bois5,972 views

"Simulation of rubber-like materials is usually based on hyperelasticity. If strain-rate dependency has to be considered viscous dampers are added to the rheological model. A disadvantage of such a description is timeconsuming parameter identification associated with the damping constants. In this paper, a tabulated formulation is presented which allows fast generation of input data based on uniaxial static and dynamic tensile tests at different strain rates. Unloading, i.e. forming of a hysteresis, can also be modeled easily based on a damage formulation. We show the theoretical background and algorithmic setup of our model which has been implemented in the explicit solver LS-DYNA [1]-[3]. Apart from purely numerical examples, the validation of a soft and a hard rubber under loading and subsequent unloading at different strain rates is shown."

Read full post
AutomotiveHigh Speed TestingHyperelasticLS-DYNAMechanicalRate DependencyResearch PapersRubbersYielding/Failure Analysis