High Speed Testing

Material Insights by Technical Interest

High Speed Testing

A Material Model for Transversely Anisotropic Crushable Foams in LS-DYNA

July 27, 2015by Paul Du Bois6,014 views

"Recently new materials were introduced to enhance different aspects of automotive safety while minimizing the weight added to the vehicle. Such foams are no longer isotropic but typically show a preferred strong direction due to their manufacturing process. Different stress/ strain curves are obtained from material testing in different directions. A new material model was added to the LS-DYNA code in order to allow a correct numerical simulation of such materials. Ease-of-use was a primary concern in the development of this user-subroutine: we required stress/ strain curves from material testing to be directly usable as input parameters for the numerical model without conversion. The user-subroutine is implemented as MAT_TRANSVERSELY_ANISOTROPIC_CRUSHABLE_FOAM, Mat law 142 in LS-DYNA Version 960-1106. In this paper we summarize the background of the material law and illustrate some applications in the field of interior head-impact. The obvious advantage of incorporating such detail in the simulation lies in the numerical assessment of impacts that are slightly offset with respect to the foam’s primary strength direction."

Read full post

Development of Material Input Data for Solid Elements under Crash Loads

July 27, 2015by Paul Du Bois5,760 views

"Heavy trucks have large masses and only small deformation zones. Because of this, they are loaded relatively severe in case of a crash. Under those conditions structural response is characterised not only by plastic deformation but also by failure in terms of cracks or fracture. Hence, failure prediction is essential for designing such parts. The following article describes the procedure of generating material models for failure prognosis of solid parts in the Commercial Vehicles Division at Daimler. Sheet metal parts are mostly discretised by shell elements. In this case the state of stress is characterized by hydrostatic pressure over von-Mises effective stress, the so-called triaxiality. For many real-life load cases which can be modeled by thin shells this ratio is between –2/3 and –2/3. Within this range the Gurson material model with the Tvergaard Needlemann addition leads to sufficiently accurate results. Furthermore, the Gurson material model allows considering the effect of element size, which amongst others is important for ductile materials. Most often however, in the case of solid parts the state of stress is more complex, which results in a triaxiality smaller than –1 or larger than 2/3. Gurson material models are usually validated based on shell meshes and tensile tests with flat bar specimen. If applied to solid parts, these models tend to underpredict failure . Thus, for solid parts the GURSON_JC material model is used. The Johnson Cook parameters are derived from an existing Gurson material model. Afterwards the material model is adapted to test results by modifying the load curve giving failure strain against triaxiality. This requires tensile tests"

Read full post

Automotive High Speed Testing LS-DYNA Mechanical Metals Rate Dependency Research Papers Validation Yielding/Failure Analysis

Experimental and Numerical Investigation of Fracture in Aluminium

July 27, 2015by Paul Du Bois5,801 views

"To assess the problem of containment after a blade-off accident in an aero-engine by numerical simulation the FAA has instigated a research effort concerning failure prediction in a number of relevant materials. Aluminium kicked off the program which involved an intensive testing program providing failure data under different states of stress, different strain rates and different temperatures. In particular split Hopkinson bars were used to perform dynamic punch tests on plates of different thicknesses allowing to investigate the transition between different failure modes such as petaling and plugging. Ballistic impact tests were performed at NASA GRC for the purpose of validation. This paper focuses on the numerical simulation effort and a comparison with experimental data is done. The simulations were performed with LS-DYNA and a tabulated version of the Johnson-Cook material law was developed in order to increase the generality, flexibility and user-friendliness of the material model."

Read full post

Aerospace and Defense High Speed Testing LS-DYNA Mechanical Metals Research Papers Validation Yielding/Failure Analysis

A Constitutive Formulation for Polymers Subjected to High Strain Rates

July 27, 2015by Paul Du Bois5,325 views

"Reliable prediction of the behavior of structures made from polymers is a topic under considerable investigation in engineering practice. Especially, if the structure is subjected to dynamic loading, constitutive models considering the mechanical behavior properly are still not available in commercial finite element codes yet. In our paper, we present a new constitutive law for polymers which recovers important phenomena like necking, crazing, strain rate dependency, unloading behavior and damage. In particular, different yield surfaces in compression and tension and strain rate dependent failure, the latter with damage induced erosion, is taken into account. All relevant parameters are given directly in the input as load curves, i.e. time consuming parameter identification is not necessary. Moreover, the models by von Mises and Drucker-Prager are included in the description as special cases. With the present formulation, standard verification test can be simulated successfully: tensile and compression test, shear test and three point bending tests."

Read full post

Automotive High Speed Testing LS-DYNA Mechanical Plasticity Plastics Rate Dependency Research Papers Yielding/Failure Analysis

A Comparative Review of Damage and Failure Models and a Tabulated Generalization

July 27, 2015by Paul Du Bois7,793 views

"Reliable prediction of damage and failure in structural parts is a major challenge posed in engineering mechanics. Although solid material models predicting the deformation behaviour of a structure are increasingly available, reliable prediction of failure remains still open. With SAMP (a Semi-Analytical Model for Polymers), a general and flexible plasticity model is available in LS-DYNA since version 971. Although originally developed for plastics, the plasticity formulation in SAMP is generally applicable to materials that exhibit permanent deformation, such as thermoplastics, crushable foam, soil and metals. In this paper, we present a generalized damage and failure procedure that has been implemented in SAMP and will be available in LS-DYNA soon. In particular, important effects such as triaxiality, strain rate dependency, regularization and non-proportional loading are considered in SAMP. All required physical material parameters are provided in a user-friendly tabulated way. It is shown that our formalism includes many different damage and failure models as special cases, such as the well-known formulations by Johnson-Cook, Chaboche, Lemaitre and Gurson among others. "

Read full post

Automotive High Speed Testing LS-DYNA Mechanical Plasticity Plastics Rate Dependency Research Papers Yielding/Failure Analysis

A Simplified Approach for Strain-Rate Dependent Hyperelastic Materials with Damage

July 22, 2015by Paul Du Bois5,972 views

"Simulation of rubber-like materials is usually based on hyperelasticity. If strain-rate dependency has to be considered viscous dampers are added to the rheological model. A disadvantage of such a description is timeconsuming parameter identification associated with the damping constants. In this paper, a tabulated formulation is presented which allows fast generation of input data based on uniaxial static and dynamic tensile tests at different strain rates. Unloading, i.e. forming of a hysteresis, can also be modeled easily based on a damage formulation. We show the theoretical background and algorithmic setup of our model which has been implemented in the explicit solver LS-DYNA [1]-[3]. Apart from purely numerical examples, the validation of a soft and a hard rubber under loading and subsequent unloading at different strain rates is shown."

Read full post

Automotive High Speed Testing Hyperelastic LS-DYNA Mechanical Rate Dependency Research Papers Rubbers Yielding/Failure Analysis

A semi-analytical model for polymers subjected to high strain rates

July 22, 2015by Paul Du Bois5,770 views

"Reliable prediction of the behaviour of structures made from polymers is a topic under considerable investigation in engineering practice. Especially, if the structure is subjected to dynamic loading, constitutive models considering the mechanical behaviour properly are still not available in commercial finite element codes. First, we give an overview of material laws for thermoplastics and show how the behaviour can be characterized and approximated by using visco-elasticity and metal plasticity, respectively. Experimental work is presented to point out important phenomena like necking, strain rate dependency, unloading behaviour and damage. A constitutive model including the experimental findings is derived. In particular, different yield surfaces in compression and tension and strain rate dependent failure, the latter with damage induced erosion, need to be taken into account. With the present formulation, standard verification tests can be simulated successfully. Also, an elastic damage model is used to approximate the unloading behaviour of thermoplastics adequately."

Read full post

Automotive High Speed Testing LS-DYNA Mechanical Rate Dependency Research Papers Yielding/Failure Analysis

The Influence of Permanent Volumetric Deformation on the Reduction of the Load Bearing Capability of Plastic Components

July 22, 2015by Paul Du Bois5,463 views

"During the past years polymer materials have gained enormous importance in the automotive industry. Especially their application for interior parts to help in passenger safety load cases and their use for bumper fascias in pedestrian safety load cases have driven the demand for much more realistic finite element simulations. For such applications the material model 187 (i.e. MAT_SAMP-1) in LS-DYNA® has been developed. In the present paper the authors show how the parameters for the rather general model may be adjusted to allow for the simulation of crazing effects during plastic loading. Crazing is usually understood as inelastic deformation that exhibits permanent volumetric deformations. Hence a material model that is intended to be applied for polymer components that show crazing effects during the experimental study, should be capable to produce the correct volumetric strains during the respective finite element simulation. The paper discusses the real world effect of crazing, the ideas to capture these effect in a numerical model and exemplifies the theoretical ideas with a real world structural component finite element model."

Read full post

Automotive High Speed Testing LS-DYNA Mechanical Plastics Rate Dependency Research Papers

A Simplified Approach to the Simulation of Rubber-like Materials under Dynamic Loading

April 28, 2015by Paul Du Bois5,554 views

"The simulation of rubber materials is becoming increasingly important in automotive crashworthiness simulations. Although highly sophisticated material laws are available in LS-DYNA to model rubber parts, the determination of material properties can be non-trivial and time consuming. In many applications, the rubber component is mainly loaded uniaxially at rather high strain rates. In this paper a simplified material model for rubber is presented allowing for a fast generation of input data based on uniaxial static and dynamic test data."

Read full post

Automotive High Speed Testing Hyperelastic LS-DYNA Mechanical Rate Dependency Research Papers Rubbers

Validation of Simulation Results Through Use of DIC Techniques

October 28, 2014by DatapointLabs6,167 views

It has long been desired to quantify the accuracy of simulation results. Through developments in digital image correlation (DIC) techniques, it is now possible to quantify the deviation between simulation and real life experimentation. In this paper, three-dimension DIC measurements of deformed parts are compared to deformed surfaces predicted in simulation. Using DIC, it is possible to import deformed surface elements from simulation and map the magnitude of deviation from the measurements of the actual deformed shape.

Read full post

ANSYS High Speed Testing Nonlinear Material Models Presentations Structural Analysis Validation