A Framework for the Calibration and Validation of Multiscale Material Models
Multiscale material models are being increasingly applied for high-level simulation of complex materials, such as continuous reinforced material products (unidirectional and woven product forms). These multiscale material models require input data from a minimum of experimental tests, which are then used to characterize a multiscale material model that can be used in structural simulations within a variety of commercial finite element solvers, including OptiStruct, RADIOSS, Abaqus, and LS-Dyna. Using these models, it is possible is to predict the performance of layups from single layer properties, as well as performance of these composites under complex loadings. We present a framework where the required experimental data are collected, including a process for maintaining traceability and consistency of the experimental data using the Matereality software. Experimental test data are transmitted to the HyperWorks Multiscale Designer software for development of an appropriate multiscale material model. The resulting multiscale material model data is stored within Matereality linked to the source experimental data. Different manufactured layups are tested and compared to simulation in a validation step which provides a measure of the solution accuracy.
Read full postDetermination and Use of Material Properties for Finite Element Analysis: Book Review
This book is intended to be a companion to the NAFEMS book, "An Introduction to the Use of Material Models in FE". It informs Finite Element Analysis users of the manner and methodologies by which materials are tested in order to calibrate material models currently implemented in various FEA programs. While the authors seek first to satisfy the basic material models outlined in the companion book, they make important extensions to FEA used in currently active areas including explicit simulation.
Read full postDatapoint Newsletter: Winter '17, Volume 23.1
New test capabilities, Matereality v10.2, upcoming presentations
Read full postWorkshop: Testing, Modeling and Validation for Plastics & Rubber Simulation in ANSYS
Plastics exhibit non-linear viscoelastic behavior followed by a combination of deviatoric and volumetric plastic deformation until failure. Capturing these phenomena correctly in simulation presents a challenge because of limitations in commonly used material models. We follow an approach where we outline the general behavioral phenomena, then prescribe material models for handling different phases of plastics deformation. Edge cases will then be covered to complete the picture. Topics to be addressed include: Using elasto-plasticity; When to use hyperelasticity; Brittle polymers – filled plastics; Failure modes to consider; Criteria for survival; Choosing materials; Spatial non-isotropy from injection molding; Importance of residual stress; Visco-elastic and creep effects; Strain-rate effects for drop test and crash simulations; Fitting material data to FEA material models; The use of mid-stage validation as a tool to confirm the quality of simulation before use in real-life applications.
Read full postDatapoint Newsletter: Winter '18, Vol. 24.1
Focus on Validation of Simulation: CAETestBench Validation for crash, additive manufacturing, injection molding, rubber hyperelasticity; Review of NAFEMS publication on V&V.
Read full postThe Role of Material Data in the Simulation of Injection Molded Parts
The modeling of material behavior for injection molded plastics is a vital step for good simulation results. We detail the types of material data needed by various injection-molding simulation programs, factors that can affect simulation quality including test techniques and process variables such as moisture content. The case of fiber filled plastics is covered along with the extension to structural analysis applications.
Read full postUsing an Intermediate Validation Step to Increase CAE Confidence
Simulations contain assumptions and uncertainties that a designer must evaluate to obtain a measure of accuracy. The assumptions of the product design can be differentiated from the ones for the solver and material model through the use of a mid-stage validation. An open loop validation uses a controlled test on a standardized part to compare results from a simulation to the physical experiment. From the validation, confidence in the material model and solver is gained. In this study, the material properties of a polypropylene are tested to characterize for an *ELASTIC *PLASTIC model in ABAQUS. A validation of a quasi-static three-point bending experiment of a parallel ribbed plate is then performed and simulated. A comparison of the strain fields resulting from the complex stress state on the face of the ribs obtained by digital image correlation (DIC) vs. simulation is used to quantify the simulation's fidelity.
Read full postChallenges in the Modeling of Plastics in Computer Simulation
Finite-element analysis and injection-molding simulation are two technologies that are seeing widespread use today in the design of plastic components. Limitations exist in our ability to mathematically describe the complexity of polymer behavior to these software packages. Material models commonly used in finite-element analysis were not designed for plastics, making it difficult to correctly describe non-linear behavior and plasticity of these complex materials. Time-based viscoelastic phenomena further complicate analysis. Dealing with fiber fillers brings yet another layer of complexity. It is vital to the plastics engineer to comprehend these gaps in order to make good design decisions. Approaches to understanding and dealing with these challenges, including practical strategies for everyday use, will be discussed.
Read full post