A Comparative Review of Damage and Failure Models and a Tabulated Generalization

July 27, 2015•by Paul Du Bois•7,793 views

"Reliable prediction of damage and failure in structural parts is a major challenge posed in engineering mechanics. Although solid material models predicting the deformation behaviour of a structure are increasingly available, reliable prediction of failure remains still open. With SAMP (a Semi-Analytical Model for Polymers), a general and flexible plasticity model is available in LS-DYNA since version 971. Although originally developed for plastics, the plasticity formulation in SAMP is generally applicable to materials that exhibit permanent deformation, such as thermoplastics, crushable foam, soil and metals. In this paper, we present a generalized damage and failure procedure that has been implemented in SAMP and will be available in LS-DYNA soon. In particular, important effects such as triaxiality, strain rate dependency, regularization and non-proportional loading are considered in SAMP. All required physical material parameters are provided in a user-friendly tabulated way. It is shown that our formalism includes many different damage and failure models as special cases, such as the well-known formulations by Johnson-Cook, Chaboche, Lemaitre and Gurson among others. "

Accuracy Issues in the Simulation of Quasi-Static Experiments for the Purpose of Mesh Regularization

July 22, 2015•by Paul Du Bois•5,676 views

Generating a LS-DYNA material model from cupon-level quasi-static experimental data, developing appropriate failure characteristics, and scaling these characteristics to mesh sizes appropriate for a variety of simulation models requires a regularization procedure. During an Investigation of an anisotropic material model for extruded aluminum, numerical accuracy issues led to unrealistic mesh regularization curves and non-physical simulation behavior. Sensitivity problems due to constitutive material behavior, small mesh sizes, single precision simulations, and simulated test velocity all contributed to these accuracy issues. Detailed analysis into the sources of innaccuracy led to the conclusion that in certain cases, double precision simulations are necesscary for accurate material characterization and mesh regularization.

A Simplified Approach for Strain-Rate Dependent Hyperelastic Materials with Damage

July 22, 2015•by Paul Du Bois•5,972 views

"Simulation of rubber-like materials is usually based on hyperelasticity. If strain-rate dependency has to be considered viscous dampers are added to the rheological model. A disadvantage of such a description is timeconsuming parameter identification associated with the damping constants. In this paper, a tabulated formulation is presented which allows fast generation of input data based on uniaxial static and dynamic tensile tests at different strain rates. Unloading, i.e. forming of a hysteresis, can also be modeled easily based on a damage formulation. We show the theoretical background and algorithmic setup of our model which has been implemented in the explicit solver LS-DYNA [1]-[3]. Apart from purely numerical examples, the validation of a soft and a hard rubber under loading and subsequent unloading at different strain rates is shown."

A semi-analytical model for polymers subjected to high strain rates

July 22, 2015•by Paul Du Bois•5,770 views

"Reliable prediction of the behaviour of structures made from polymers is a topic under considerable investigation in engineering practice. Especially, if the structure is subjected to dynamic loading, constitutive models considering the mechanical behaviour properly are still not available in commercial finite element codes. First, we give an overview of material laws for thermoplastics and show how the behaviour can be characterized and approximated by using visco-elasticity and metal plasticity, respectively. Experimental work is presented to point out important phenomena like necking, strain rate dependency, unloading behaviour and damage. A constitutive model including the experimental findings is derived. In particular, different yield surfaces in compression and tension and strain rate dependent failure, the latter with damage induced erosion, need to be taken into account. With the present formulation, standard verification tests can be simulated successfully. Also, an elastic damage model is used to approximate the unloading behaviour of thermoplastics adequately."

The Influence of Permanent Volumetric Deformation on the Reduction of the Load Bearing Capability of Plastic Components

July 22, 2015•by Paul Du Bois•5,463 views

"During the past years polymer materials have gained enormous importance in the automotive industry. Especially their application for interior parts to help in passenger safety load cases and their use for bumper fascias in pedestrian safety load cases have driven the demand for much more realistic finite element simulations. For such applications the material model 187 (i.e. MAT_SAMP-1) in LS-DYNA® has been developed. In the present paper the authors show how the parameters for the rather general model may be adjusted to allow for the simulation of crazing effects during plastic loading. Crazing is usually understood as inelastic deformation that exhibits permanent volumetric deformations. Hence a material model that is intended to be applied for polymer components that show crazing effects during the experimental study, should be capable to produce the correct volumetric strains during the respective finite element simulation. The paper discusses the real world effect of crazing, the ideas to capture these effect in a numerical model and exemplifies the theoretical ideas with a real world structural component finite element model."

Advances in the Measurement and Modeling of Plastics for Impact Simulations

April 28, 2015•by Hubert Lobo•5,312 views

Comparison of Crash Models for Ductile Plastics

April 28, 2015•by DatapointLabs•6,503 views

There is interest in quantifying the accuracy of different material models being used in LS-DYNA today for the modeling of plastics. In our study, we characterize two ductile, yet different materials, ABS and polypropylene for rate dependent tensile properties and use the data to develop material parameters for the material models commonly used for plastics: MAT_024 and its variants, MAT_089 and MAT_187. We then perform a falling dart impact test which produces a complex multi-axial stress state and simulate this experiment using LS-DYNA. For each material model we are able to compare simulation to actual experiment thereby obtaining a measure of fidelity of the simulation to reality. In this way, we can assess the benefits of using a particular material model for plastics simulation.

A Simplified Approach to the Simulation of Rubber-like Materials under Dynamic Loading

April 28, 2015•by Paul Du Bois•5,554 views

"The simulation of rubber materials is becoming increasingly important in automotive crashworthiness simulations. Although highly sophisticated material laws are available in LS-DYNA to model rubber parts, the determination of material properties can be non-trivial and time consuming. In many applications, the rubber component is mainly loaded uniaxially at rather high strain rates. In this paper a simplified material model for rubber is presented allowing for a fast generation of input data based on uniaxial static and dynamic test data."

Challenges in the Modeling of Plastics in Computer Simulation

March 12, 2015•by DatapointLabs•7,256 views

Finite-element analysis and injection-molding simulation are two technologies that are seeing widespread use today in the design of plastic components. Limitations exist in our ability to mathematically describe the complexity of polymer behavior to these software packages. Material models commonly used in finite-element analysis were not designed for plastics, making it difficult to correctly describe non-linear behavior and plasticity of these complex materials. Time-based viscoelastic phenomena further complicate analysis. Dealing with fiber fillers brings yet another layer of complexity. It is vital to the plastics engineer to comprehend these gaps in order to make good design decisions. Approaches to understanding and dealing with these challenges, including practical strategies for everyday use, will be discussed.

Software for Creating LS-DYNA Material Model Parameters from Test Data 

October 8, 2014•by DatapointLabs•5,988 views

LS-DYNA software contains a wealth of material models that allow for the simulation of transient phenomena. The Matereality® CAE Modeler is a generalized pre-processor software used to convert material property data into material parameters for different material models used in CAE. In a continuation of previously presented work, we discuss the extension of the CAE Modeler software to commonly used material models beyond MAT_024. Software enhancements include advanced point picking to perform extrapolations beyond the tested data, as well as the ability to fine-tune the material models while scrutinizing the trends shown in the underlying raw data. Advanced modeling features include the ability to tune the rate dependency as well as the initial response. Additional material models that are quite complex and difficult to calibrate are supported, including those for hyperelastic and viscoelastic behavior. As before, the written material cards are directly readable into the LS-DYNA software, but now they can also be stored and catalogued in a material card library for later reuse.