Material Insights by Technical Interest

Nonlinear Material Models

Sort byDateViews

Using an Intermediate Validation Step to Increase CAE Confidence

by DatapointLabs7,360 views

Simulations contain assumptions and uncertainties that a designer must evaluate to obtain a measure of accuracy. The assumptions of the product design can be differentiated from the ones for the solver and material model through the use of a mid-stage validation. An open loop validation uses a controlled test on a standardized part to compare results from a simulation to the physical experiment. From the validation, confidence in the material model and solver is gained. In this study, the material properties of a polypropylene are tested to characterize for an *ELASTIC *PLASTIC model in ABAQUS. A validation of a quasi-static three-point bending experiment of a parallel ribbed plate is then performed and simulated. A comparison of the strain fields resulting from the complex stress state on the face of the ribs obtained by digital image correlation (DIC) vs. simulation is used to quantify the simulation's fidelity.

Read full post
AbaqusAutomotiveBiomedicalConsumer ProductsFurnitureHome AppliancesMaterial SupplierNonlinear Material ModelsPackagingPlasticityPlasticsResearch PapersStructural AnalysisToys/Sporting GoodsValidation

Thermoplastic Material Testing for Use in SIGMASOFT and the Effect of Moisture on PA 6/6

by DatapointLabs5,817 views

Thermoplastic materials are one of the largest categories of materials to be injection molded. Moisture-sensitive materials can lead to issues in the molding process. Simulation of the injection molding process requires sophisticated and exact material properties to be measured. This presentation discusses the testing required to characterize a thermoplastic material for use in SIGMASOFT, as well as the effects of moisture on viscosity measurement of a moisture-sensitive material. Consequences of basing designs on wet or dry materials are covered. Implementation of material data into the software to produce a successful injection molding simulation simulation is described.

Read full post
CAE Vendor/SupplierInjection MoldingNonlinear Material ModelsPlasticsPresentationsRheologySIGMASOFT

Nonlinear viscoelastic modeling for foams

by Paul Du Bois5,719 views

Lightweight design is one of the major principles in automotive engineering and has made polymer materials to inherent parts of modern cars. In addition to their lightweight thermoplastics, elastomers, fabric and composites also incur important functions in passive safety. In the age of virtual prototyping, assuring these functions requires the accurate modeling of the mechanical behavior of each component. Due to their molecular structure, polymer materials often show viscoelastic characteristics such as creep, relaxation and recovery. However, considering the general state of the art in crash simulation, the viscoelastic characteristics are mainly neglected or replaced by viscoplastic or hyperelastic and strain rate dependent material models. This is either due to the available material models that are often restricted to linear viscoelasticity and thus cannot model the experimental data or due to the time consuming parameter identification. In this study, a nonlinear viscoelastic material model for foams is developed and implemented as a user material subroutine in LS-DYNA. The material response consists of an equilibrium and a non-equilibrium part. The first one is modeled with a hyperelastic formulation based on the work of Chang [8] and formerly implemented as *MAT_FU_CHANG_FOAM in LS-DYNA (*MAT_083). The second one includes the nonlinear viscoelastic behavior following the multiple integral theory by Green and Rivlin [9]. The polyurethane foam Confor CF-45 used as part of the legform impactor in pedestrian safety was chosen for its highly nonlinear viscoelastic properties to test the presented approach. The investigation shows the ability of the method to reliably simulate some important nonlinear viscoelastic phenomena such as saturation.

Read full post
AutomotiveFoamsLS-DYNAMechanicalNonlinear Material ModelsResearch PapersViscoelastic

Accuracy Issues in the Simulation of Quasi-Static Experiments for the Purpose of Mesh Regularization

by Paul Du Bois5,676 views

Generating a LS-DYNA material model from cupon-level quasi-static experimental data, developing appropriate failure characteristics, and scaling these characteristics to mesh sizes appropriate for a variety of simulation models requires a regularization procedure. During an Investigation of an anisotropic material model for extruded aluminum, numerical accuracy issues led to unrealistic mesh regularization curves and non-physical simulation behavior. Sensitivity problems due to constitutive material behavior, small mesh sizes, single precision simulations, and simulated test velocity all contributed to these accuracy issues. Detailed analysis into the sources of innaccuracy led to the conclusion that in certain cases, double precision simulations are necesscary for accurate material characterization and mesh regularization.

Read full post
Aerospace and DefenseAutomotiveExtrusionLS-DYNAMechanicalMetalsNonlinear Material ModelsResearch PapersYielding/Failure Analysis

Challenges in the Modeling of Plastics in Computer Simulation

by DatapointLabs7,256 views

Finite-element analysis and injection-molding simulation are two technologies that are seeing widespread use today in the design of plastic components. Limitations exist in our ability to mathematically describe the complexity of polymer behavior to these software packages. Material models commonly used in finite-element analysis were not designed for plastics, making it difficult to correctly describe non-linear behavior and plasticity of these complex materials. Time-based viscoelastic phenomena further complicate analysis. Dealing with fiber fillers brings yet another layer of complexity. It is vital to the plastics engineer to comprehend these gaps in order to make good design decisions. Approaches to understanding and dealing with these challenges, including practical strategies for everyday use, will be discussed.

Read full post
AbaqusBlow MoldingDIGIMATExtrusionInjection MoldingLS-DYNAMechanicalNonlinear Material ModelsPlasticsPresentationsStructural AnalysisThermoforming

Thermoplastic Material Testing for Use in SIGMASOFT

by DatapointLabs6,067 views

Thermoplastic materials are one of the largest categories of materials to be injection molded. Simulation of the injection molding process requires sophisticated and exact material properties to be measured. This presentation will discuss the testing required to characterize a material for use in SIGMASOFT, as well as the significance of material model parameters. Differences in testing methodology for amorphous and semi-crystalline polymers will be covered, along with step-by-step implementation into the software to produce a successful injection molding simulation simulation.

Read full post
Electonics/ElectricalInjection MoldingNonlinear Material ModelsPlasticsPresentationsSIGMASOFTStructural Analysis

Validation of Simulation Results Through Use of DIC Techniques 

by DatapointLabs6,167 views

It has long been desired to quantify the accuracy of simulation results. Through developments in digital image correlation (DIC) techniques, it is now possible to quantify the deviation between simulation and real life experimentation. In this paper, three-dimension DIC measurements of deformed parts are compared to deformed surfaces predicted in simulation. Using DIC, it is possible to import deformed surface elements from simulation and map the magnitude of deviation from the measurements of the actual deformed shape.

Read full post
ANSYSHigh Speed TestingNonlinear Material ModelsPresentationsStructural AnalysisValidation

Software for Creating LS-DYNA Material Model Parameters from Test Data 

by DatapointLabs5,988 views

LS-DYNA software contains a wealth of material models that allow for the simulation of transient phenomena. The Matereality® CAE Modeler is a generalized pre-processor software used to convert material property data into material parameters for different material models used in CAE. In a continuation of previously presented work, we discuss the extension of the CAE Modeler software to commonly used material models beyond MAT_024. Software enhancements include advanced point picking to perform extrapolations beyond the tested data, as well as the ability to fine-tune the material models while scrutinizing the trends shown in the underlying raw data. Advanced modeling features include the ability to tune the rate dependency as well as the initial response. Additional material models that are quite complex and difficult to calibrate are supported, including those for hyperelastic and viscoelastic behavior. As before, the written material cards are directly readable into the LS-DYNA software, but now they can also be stored and catalogued in a material card library for later reuse.

Read full post
CompositesFoamsHigh Speed TestingInjection MoldingLS-DYNAMetalsNonlinear Material ModelsPlasticsPresentationsRubbersStructural Analysis

Plastics & Simulation 

by DatapointLabs5,532 views

Plastics exhibit non-linear viscoelastic behavior followed by a combination of deviatoric and volumetric plastic deformation until failure. Capturing these phenomena correctly in simulation presents a challenge because of the inadequacy of currently used material models. We follow an approach where we outline the general behavioral phenomena, then prescribe material models for handling different phases of plastics deformation. Edge cases will then be covered to complete the picture. Topics to be addressed include: Using elasto-plasticity; When to use hyperelasticity; Brittle polymers – filled plastics; Failure modes to consider; Criteria for survival; Choosing materials; Spatial non-isotropy from injection molding; Importance of residual stress; Visco-elastic and creep effects; Strain-rate effects for drop test and crash simulations; Fitting material data to FEA material models.

Read full post
ANSYSHigh Speed TestingNonlinear Material ModelsPlasticsPresentations